Instrumenten (Petro) volgens normen.

DIGITAL PENETROMETER FOR BITUMENS ASTM D 5 - IP 49

The apparatus consists of a penetrometer with electrically motorized head combined with a manual gear that permits a fine adjustment of the cone position right upon the bitumen sample: the results are showed on a digital display placed, together with an electronic timer in an independent control box. Other Standards : IP 49 - ISO 3997 – DIN 52010

EXTERNAL COOLER FOR PENETRATION SAMPLE CONDITIONING ASTM D 5 – ASTM D 217

The equipment consists of a compact benchtop circulation cooler to be placed below the bench supporting the penetrometer: thanks to a built-in cooling compressor, temperature can be maintained in a range from 0 to 50°C with 0.1°C precision. A pump permits to circulate the liquid in the transfer dish placed on the penetrometer.

APPARATUS FOR THE DETERMINATION OF LOSS ON HEATING OF ASPHALTIC COMPOUNDS ASTM D 6 – D 1754 – IP 45

The apparatus consists of a convection oven manufactured as described in the ASTM E 145 specification (type IB), suitable for temperatures up to 180°C and equipped with a rotating shelf inside. An electronic controlled motor with gear reducer mounted on the top of the oven rotates the shelf at 5.5 rpm.

AUTOMATIC SOFTENING POINT TESTER ASTM D 36 – IP 58

The softening point is the temperature at which a disk of the sample held within a horizontal ring is forced downward a distance of 25.4 mm under the mass of a steel ball as the sample is heated at a prescribed rate in a water or glycerin bath.

TAG AUTOMATIC FLASH POINT TESTER ASTM D 56

The apparatus consists of a benchtop model which houses the water bath, the operating mechanism and microprocessor controller. The apparatus performs the test automatically, providing heat to the sample a the correct rate and introducing the flame at the correct intervals. When a flash point is detected, the result remains shown on the display until the operator’s acknowledgement.

MANUAL/SEMI-AUTOMATIC DISTILLATION ASTM D 86

This test method covers the distillation of gasoline,benzines,aviation turbine fuels,kerosenes,tractor fuels,gas oils,diesel fuels,furnace oils and simular products Other Standards : IP123 – ISO 3405 – DIN 51751

AUTOMATIC DISTILLATION ASTM D 86

This test method covers the distillation of gasoline,benzines,aviation turbine fuels,kerosenes,tractor fuels,gas oils,diesel fuels,furnace oils and simular products Other Standards : IP123 – ISO 3405 – DIN 51751

DETERMINATION OF WATER AND SEDIMENT by CENTRIFUGE METHOD ASTM D 91

This testmethod describes a quick method for determination of water and sediment in crude oil,fuel oils and distillate fuels. The centrifuge method is also used in many other standard methods as there are: determination of precipitation number, demulsibility characteristics, trace sediments and insolubles in used oils. Other Methods : ASTM D 96 – D 893 – D1796 – D 2273 – D 2709 – D 2711 – D 4007 - IP 75 – IP145 – IP 359 , ISO 3734 , DIN 51793

CLEVELAND FLASH POINT TESTER ASTM D 92 - IP 36

The apparatus consists of a benchtop steel case supporting the electrical heater, the gas ignitor and the thermometer support. Other Standards: ISO 2592

CLEVELAND AUTOMATIC FLASH POINT TESTER ASTM D 92 - IP 36

The apparatus is a benchtop model which houses the electric heater, the operating mechanism and microprocessor controller. The apparatus performs the test automatically, providing heat to the sample at the correct rate and passing the flame over the cup at the correct intervals. When a flash point is detected, the result remains shown on the display until the operator acknowledgement. Other Standards: ISO 2592

PENSKY MARTENS FLASH POINT TESTER ASTM D 93 - IP 34

The apparatus is a benchtop model which houses the air bath stove and the stirrer motor: differently from other apparatus on the market, our instrument is fitted with a fan that cools down the stove quickly after the test. Other Standards: ISO 2719 – DIN 51758

PENSKY MARTENS AUTOMATIC FLASH POINT TESTER ASTM D 93 - IP 34

The apparatus is a benchtop model which houses the air bath stove, the operating mechanism and the microprocessor controller. The apparatus performs the test automatically, providing heat to the sample at the correct rate and introducing the flame at the correct intervals. When a flash point is detected, the value remains shown on the display until the operator’s acknowledgement. Other Standards: ISO 2719 – DIN 51758

MECHANICALLY REFRIGERATED CLOUD AND POUR POINT CABINET ASTM D 97 – D 2500 – IP 15

The apparatus consists in a floor-mounted cabinet containing one, two, three or four aluminium blocks with four jackets: the temperature of each block is maintained at a fixed temperature by means of electronic thermoregulators. Every block has its independent cooling compressor and the top plate is fitted with a low voltage defrosting device.

POUR POINT AUTOMATIC TESTER ASTM D 97

The analyser is a benchtop model that contains the cooling compressor for 1 up to 3 test positions, the analytical heads and the interface board.The analyser is running under Windows™ software to perform fully automatic analysis, store data, produce graphs and allow calibration and diagnostic.

DUCTILITY MACHINE ASTM D 113 - D 5976 - IP 32 - IS 1208

The apparatus consists of a constant temperature bath capable to work in the range from -10 to 40 °C (thanks to a built-in cooling compressor) with an electrically powered tractor that pulls apart at a determined speed the two ends of two briquet specimens: the elongation is measured by means of a pointer on the tractor and a graduated scale fixed to the cover. Other Standards: DIN 52013

COMPUTER CONTROLLED DUCTILITY MACHINE ASTM D 113 - D 5976 - IP 32 - IS 1208

The apparatus consists of a constant temperature bath capable to work in the range from -10 to 40 °C (thanks to a built-in cooling compressor) with an electrically powered tractor that pulls apart at an selectable speed the two ends of two briquet specimens:..........

APPARATUS FOR THE DETERMINATION OF COPPER CORROSION OF PETROLEUM PRODUCTS ASTM D 130

The apparatus, suitable for the execution of the test at 40, 50 and at 100°C, consists of a benchtop steel case containing a stainless steel bath with a four-hole cover to allow the introduction of the bombs or the test tubes and a control box containing all the electronics. Other Standards: IP 154 – ISO 2160 – DIN 51811

BATH FOR THE DETERMINATION OF THE COPPER CORROSION ASTM D130 - IP227

The apparatus, consists of a benchtop steel case containing a stainless steel bath: the cover has a series of holes suitable for both glassware for copper and silver strip corrosion tests and vessels for copper strip corrosion test. Two manifolds permit to easily connect cooling water to silver corrosion glassware.

ELECTRICALLY OPERATED GREASE WORKING MACHINE ASTM D 217 – IP 50

Worked penetration results may be used to establish the consistency of lubricating greases after prolonged working. The change in worked penetration results on a grease after prolonged working are believed to be a measure of its shear stability under the conditions of the test.

DIGITAL PENETROMETER FOR GREASE, WAX AND PETROLATUM ASTM D 217, D 1321, D 1403 - IP 50, IP 310

The penetration is the depth, in tenths of a millimetre, that the standard cone penetrates the sample under prescribed conditions of weight, time and temperature.

APPARATUS FOR THE DETERMINATION OF REID VAPOR PRESSURE OF GASOLINE ASTM D 323 - IP 69

The apparatus consists of a floor mounted water bath with a support for three vapour pressure cylinders. Other Standards: ISO 3007 – EN 12

APPARATUS FOR THE DETERMINATION OF EXISTENT GUM IN FUELS BY JET EVAPORATION ASTM D 381 - IP 131

The apparatus consists of a benchtop case which houses an aluminium heating block. Two versions are available: one for the “Air Jet” test on gasoline and one for both the “Air and Steam Jet” tests with a built-in steam superheater. Steam generator and air blower are also available. Other Standards: ISO 6246 – DIN 51776

LOW-TEMPERATURE BATH FOR VISCOSITY DETERMINATION ASTM D 445 - IP 71

The apparatus consists of a benchtop case hosting the bath and the cooling compressor. One important feature of this apparatus is that the bath is a stainless steel tank (no double-wall glass beaker is used) with a large tempered glass window for a clear view of the inside. The cover of the bath can host two Cannon-Fenske or Ubbelohde capillaries. Other Standards: ISO 3104 – DIN 51366

ULTRATHERMOSTAT FOR VISCOSITY DETERMINATION ASTM D 445 - IP 71

The apparatus consists of a benchtop steel case containing a pyrex jar, 330 mm deep, that permits the use of a wide range of viscometer tubes. Up to six viscometer tubes can be inserted on a turntable that allows to carry in the front of the jar the tube on which the operator is working on. Other Standards: ISO 3104 – DIN 51366

KINEMATIC VISCOSITY DETERMINATION of TRANSPARENT and OPAQUE LIQUIDS ASTM D 445 - IP 71

This test method covers the determination of the kinematic viscosity of liquid petroleum products, both transparent and opaque. Measuring principle is the time needed for a specific volume of liquid to flow under gravity through a calibrated capillary viscotube. Other Standards: ISO 3104 – DIN 51366

DETERMINATION OF ASH ASTM D 482

This method covers the determination of ash from distillate and residual fuels, crude oils, lubricating oils, waxes and other petroleum products. Other Standards : ASTM D 482 – D 874 – D 1026 – D 4422 – IP 4 – IP 163 – ISO 3987 - DIN 51352 – DIN 51575 – DIN 51803

APPARATUS FOR THE DETERMINATION OF RAMSBOTTOM CARBON RESIDUE OF PETROLEUM PRODUCTS ASTM D 524 - IP 1

The apparatus consists of a benchtop case containing a five-place steel furnace. It can reach temperatures up to 600 °C. Other Standards: ISO 4262

APPARATUS FOR THE DETERMINATION OF OXIDATION STABILITY OF GASOLINE AND AVIATION FUELS ASTM D 525 - A

The apparatus consists of a benchtop case containing a stainless steel tank or an aluminium block with holes for the bombs, both suitable to reach the test temperature of 100 °C. The advantage of the aluminium block toward the water bath is the elimination of periodical maintenance and cleaning: besides the instrument become more robust and safe in use.

APPARATUS FOR THE DETERMINATION OF OXIDATION STABILITY OF GASOLINE AND AVIATION FUELS ASTM D 525 - A

The apparatus consists of a benchtop case containing an aluminium block or a water bath. A software under Windows 9x acquires pressure from the bombs and plots them on a graph on the screen allowing data retrieval and report printout (printer supplied as option) at the end of the test. The apparatus can be supplied with a compact Panel PC with 12” TFT screen, with a desktop PC or can be connected to the user’s PC. Other Standards: ISO 7536 – DIN 51780

APPARATUS FOR THE DETERMINATION OF DROPPING POINT OF LUBRICATING GREASE ASTM D 566 - D 2265 - IP 132

The dropping point is the temperature at which the grease passes from a semisolid to a liquid state under the conditions of test. Cooperative testing indicates that in general, dropping points by test method D 566 and test method D 2265 are in agreement.